Measuring functions

Level

Input level (effective value) in volts, dBu or dBV, as well as signal frequency. Relative measurements to freely selectable references. With a measuring microphone, the ML1 also becomes a high-quality sound level meter (SPL/LEQ).

THD+N

Measurement of THD+N (THD with noise) and the second to fifth harmonic distortion as a dB value or in %. Display of fundamental frequency, input level and signal symmetry. Extensive filters.

Frequency response

The Minilyzer automatically recognizes the start of a sweep sequence with any step size and saves the measured frequency response. Graphical display with numerical cursor and zoom functions.

Polarity

Incorrectly connected loudspeakers are reliably detected with the ML1 and the
built-in microphone. The same measurement via the XLR input is ideal for cable polarity tests.

Time sweep

The time sweep records the course of the RMS level, the frequency and the THD+N value simultaneously and is very well suited for observing longer test periods as well as for detecting rarely occurring faults.

Oscilloscope

The scope provides a quick overview of the waveform and immediately identifies overdriven amplifiers, noisy signals, etc. With automatic scaling and triggering as well as frequency display.

1/3rd Octave

FFT based 1/3rd octave real-time analyzer. Automatic display of the most energetic band helps to eliminate feedback. Adjustable display time constant, zoom and data cursor. Electrical (dBu) and acoustic measurements (SPL scale) are supported.

vu/PPM

Precise level measurement for optimum electrical leveling according to IEC60268 (ppm = Peak Program Meter). All common standards are supported (Type I, Type IIA, Nordic); adjustable reference levels.

Induction loop measurement AFILS

The Minilyzer together with the optional MiniLINK USB interface measures induction loops AFILS according to standard IEC60118. A complete measurement menu can be activated in the Minilyzer according to the requirements of the standard, including calibration for a customer-specific field strength sensor.

Key features:

• Latency-free transmission (<1ms)
• Uncompressed transmission in 4:2:2 10-bit up to 1080p60 (3G-SDI & -HDMI)
• Very long range up to over 700m with line of sight and optimum conditions
• Optional possibility of a directional antenna on the receiver.
• Built-in cross converter (HDMI to SDI, SDI to HDMI)
• Manual frequency selection - no pairing necessary
• More stable connection thanks to preset channels and no need for DFS
• Approved for indoor operation.
• Fast connection setup
• Operates in the license-free 5Ghz ISM band

Key features:

• Height: 131.3 mm

• Width: 28.1 mm

• Depth: 12.1 mm

• Weight: 49.2 g (incl. battery)

• Motion sensor
  3D accelerometer and gyroscope

• Battery
  Battery life (rechargeable): 3 months. Depends on usage.
  Battery information: Lithium polymer battery 85 mAh

• Connectivity
  Connection type: Bluetooth Low Energy technology and 2.4 GHz wireless connection
  Wireless range: 30 m. Depends on usage and environmental conditions.

• Status indicators
  LED: Battery and connection LED

Key features:

• Non-slip, ultra-flat cable bridge made of recyclable polyurethane for indoor use.

• Zigzag connection, pre-drilled for screwing, cutting guides for shortening.

• 4 channels: 2 channels each 10 x 10 mm and 12 x 12 mm

• Meets the guidelines according to § 3 A1 of the ArbStättV

• Fire protection class B2 (DIN 4102)

• Resistant to oil, acids, solvents and petrol.

• Dimensions 86.5 x 12.5 x 2 cm, weight 1.2 kg.

• Curves and end pieces for flexible and protected cable routing.

Key features:

• Lightweight professional boom pole
• 3 m reach
• Extremely smooth extension and retraction system
• User-friendly locking mechanism
• Weight: 940 g
• Height: 3232.5 mm, width: 40 mm, depth: 40 mm

Key features:

• Maximum coffee enjoyment with up to 20 delicious coffee variations to suit your taste in combination with mild or strong coffee.
• Fold-out cup holder for different cup sizes.
• Quick and easy cleaning thanks to automatic rinsing program.
• Fast and cashless payment thanks to modern payment system.
• Possibility to import individual break-time images and company messages via USB.
• Structured, clear and evaluable counter reading of beverage consumption.
• The modern look is complemented by LED lighting (e.g. at the drinks counter).

Technical data

- Mains voltage 230 V ~ (± 10 %)
- frequency 50/60 Hz (± 2 %)
- Maximum power consumption 1,600 W
- Fuse protection installation site 10 - 16 A (individually fused)
- Dimensions H x W x D (closed) 590 x 420 x 530 mm
- Dimensions H x W x D (with lid open) 925 x 420 x 610 mm
- Weight (with products) approx. 35 kg

Measuring functions

Level

Input level (effective value) in volts, dBu or dBV, as well as signal frequency. Relative measurements to freely selectable references. With a measuring microphone, the ML1 also becomes a high-quality sound level meter (SPL/LEQ).

THD+N

Measurement of THD+N (THD with noise) and the second to fifth harmonic distortion as a dB value or in %. Display of fundamental frequency, input level and signal symmetry. Extensive filters.

Frequency response

The Minilyzer automatically recognizes the start of a sweep sequence with any step size and saves the measured frequency response. Graphical display with numerical cursor and zoom functions.

Polarity

Incorrectly connected loudspeakers are reliably detected with the ML1 and the
built-in microphone. The same measurement via the XLR input is ideal for cable polarity tests.

Time sweep

The time sweep records the course of the RMS level, the frequency and the THD+N value simultaneously and is very well suited for observing longer test periods as well as for detecting rarely occurring faults.

Oscilloscope

The scope provides a quick overview of the waveform and immediately identifies overdriven amplifiers, noisy signals, etc. With automatic scaling and triggering as well as frequency display.

1/3rd Octave

FFT based 1/3rd octave real-time analyzer. Automatic display of the most energetic band helps to eliminate feedback. Adjustable display time constant, zoom and data cursor. Electrical (dBu) and acoustic measurements (SPL scale) are supported.

vu/PPM

Precise level measurement for optimum electrical leveling according to IEC60268 (ppm = Peak Program Meter). All common standards are supported (Type I, Type IIA, Nordic); adjustable reference levels.

Induction loop measurement AFILS

The Minilyzer together with the optional MiniLINK USB interface measures induction loops AFILS according to standard IEC60118. A complete measurement menu can be activated in the Minilyzer according to the requirements of the standard, including calibration for a customer-specific field strength sensor.

Bolero Integrated harnesses the power and functionality of the Artist
ecosystem to provide an unrivaled level of connectivity.
Bolero Standalone Link has multiple plug & play features and is particularly suitable for smaller installations or mobile deployments.
Bolero Standalone 2110 (AES67) can be used to set up complex IP-based Bolero
networks without an Artist Matrix, because audio mixing and control
control functions are handled by the antennas.

The Bolero high-clarity speech codec improves speech intelligibility and optimizes the use of the RF spectrum. Compared to other DECT-based systems, Bolero can support twice as many beltpacks per antenna with the same audio bandwidth. An exclusive technology from Riedel, the so-called ADR technology, combines a unique receiver design with multiple diversity elements. This reduces the sensitivity to multipath RF reflections. As a result, Bolero can also be used in complex RF environments where other systems are severely restricted.

BOLERO Integrated

- Full Artist integration including SmartPanels and extensive I/O connectivity (SMPTE 2110-30/31 (AES67), AES3, MADI, Dante, 4-wire)
- Multiple fiber optic switch cascades for long distances.
- Signal distribution via AES67 IP network
- Setup via dedicated configuration software Director
- 500 conferences and unlimited point-to-point connections

BOLERO Standalone

- Daisy chain or redundant ring network
- Simple plug & play setup
- Redundant power supply for up to 5 antennas (EPS-1005 PSU)
- Up to 300m CAT5 cable between antennas
- External 4W and GPIO interface box (NSA-002A)
- Setup via integrated web browser
- 12 party lines and unlimited point-to-point connections
- 100 beltpacks, 100 antennas

Key features:

Key features:

• Base-to-beltpack frequency response: 100Hz - 7.1kHz
• Number of beltpacks per base station: 25
• Number of transceivers/antennas supported by the base: 10
• Number of active transceiver ports: 2, one port can support up to 1
  FSII splitter or 1 FSII transceiver.
• PC programming port: 2 LAN RJ45
• Relay port: DB15, supports one relay assigned to the SA output.
• Partyline A,B,C,D (respectively): XLR-3F, on/off termination switch, Clear-Com and RTS compatible.
• Partyline Power On/Off: A/B, C/D paired
• Partyline output voltage: 26 - 28VDC, 400mA per pair (A/B or C/D)
• 4-wire/matrix connection: 4 RJ-45
• Program input: XLR-3F, transformer isolated, line level input
• Stage announce output: XLR-3M, transformer-isolated, line level output
• Front panel headset: 4-pin plug and 5-pin socket as an option
• Front panel displays: 4 OLEDs with rotary encoders and assignable softkeys

FreeSpeak II base station

Front panel
1. USB
2. headset connector
3. headset button
4. mode button
5. menu button
6. softkeys
7. displays
8. rotary encoder for control
9. stage announcement
10. remote microphone switch-off
11. all talk
12. status LEDs
13. main level encoder
14. program level encoder

Rear panel

1. IEC mains connection (110-230 VAC)
2. earthing screw
3. external power supply connection
4. fiber optic transceiver ports (SFP)*
5. copper transceiver connections (RJ45)
6. DECT SYNC connections (RJ45)
7. 2-wire connections A,B,C,D (XLR3M)
8. 4-wire connections, 1,2,3,4 (RJ45)
9. program input (XLR3M)
10. stage announcement output (XLR3M)
11. LAN1, LAN2, (Ethercon RJ45)
12. GPIO relay (DB15F)

Indicators on the front panel:

- Antenna status, beltpack status
- External power supply connection: 12VDC
- Base station
- Programming/editing:
- Push-to-enter rotary knob

Power supply
- Input: 100-240V AC, max. 1.4A
- Output: 12V DC, 60W, 5A
- Power consumption: 12V, 4A max, 48W max
Dimensions:
1.75 x 19.0 x 10.2 inches (HxWxD)
(44 x 483 x 259 mm)
Weight: 2.5 kg (5.57 lbs)

Key features:

• Procedure: Steam generator according to the vaporizer principle
• Power: 1500W
• Fluid container: 5 liters
• Fog output: 1% -99% adjustable in 1% steps.
• Control options: DMX 512, stand alone, timer, analog 0-10V
• Heating time: 60 sec.
• Temperature control: Microprocessor controlled.
• Operating ambient temperature: 5° to 45°
• Fluid consumption: 8.9 ml/min (max. output) - 1.0 ml/min (40%)
• Weight: 16.5 kg
• Dimensions: 55 x 26.5 x 41.5 cm

Key features:

• Robust and compact
• DMX 512 standard, analog (0 - 10 V) and stand-alone operation
• Internal timer
• Settings via LED display with simple menu navigation.
• Long range up to 15 m
• Fine adjustment of the fog quantity in 1% increments
  from 0 - 99
• Continuous fog function possible
• Easy removal of the canister holder if required.
  No canister leakage and easy replacement thanks to quick-release coupling on the tank cap.
• High-quality fog fluids with different service lives for dense, white fog.

- Operating principle: Vaporizer fogger
- Heating capacity: 1300 watts
- Supply voltage: 230 V / 50 Hz
- Heating time: approx. 7 min.
- Fluid consumption: at max. output 120 ml/min. , with continuous fog 35 ml/min.
- Capacity: fluid tank 5 liters
- Fog output adjustable in 99 levels
- Output range max. 15 m
- Temperature regulation controlled by microprocessor.
- Overheating protection Heating block with thermostat, pump with temperature switch.
- Connections: DMX 512, 0 - 10 V analog
- Dimensions: (L x W x H) 47 x 23 x 24 cm
- Weight: 17 kg incl. canister